IOI Technology Corporation
Your I/O Solution Provider

U2H4+ATA11P is an USB 2.0 four-port HUB with one USB to IDE (ATA/ATAPI) bridge. U2H4+ATA11P provides three downstream USB ports, one IDE (ATA/ATAPI) port. It is ideally suited for docking station solution which need more USB port and interface for connecting two ATA devices.
It allows ATA drives (Master and Slave) to be connected to USB 2.0 serial bus in a plug-and-play fashion.

U2H4+ATA11P combines two key components:
1). Four ports USB 2.0 High Speed Hub
2). USB 2.0 to IDE(ATA/ATAPI) Bridge Board

1). Four ports USB 2.0 High Speed Hub:
U2H4+ATA11P provides high-performance four downstream USB ports.
U2H4+ATA11P is designed with Multiple Transaction Translator (MTT) USB 2.0 HUB controller.
Multiple Transaction Translator (MTT) provides individual TT control logics for each downstream port. This is a performance better choice for USB 2.0 Hub
The U2H4+ATA11P works backward compatible either when any one of downstream ports are connected to an USB 1.1 compliant device, or when the upstream port is connected to a USB 1.1 compliant host.

• Compliant with USB 2.0(Data Rate 1.5/12/480Mbps)
• 4 downstream ports
  • Two downstream ports (USB1&2) are Intel block berg-strip header (2x5/9 pin).
  • One downstream port (USB3) is Intel block berg-strip header (2x5/9 pin).
  • One downstream internal port for USB 2.0 to ATA/SATA Bridge Board
• Upstream port
  • USB B-Type connector
• Multiple transaction translator (MTT)
  • One TT per downstream port for maximum performance
• All downstream facing ports can handle high-speed (480 Mbps), full-speed (12 Mbps), and low-speed (1.5 Mbps) transaction.
• Self-powered mode operation.
• DC Power Connector
  • Floppy Disk Drive like mini 4-pin DC power connector

2). USB 2.0 to IDE(ATA/ATAPI) Bridge Board:

• USB Bus Transfer Rate: High Speed (480 Mbit) And Full Speed (12 Mbit)
• USB Bus Power: Self Powered Mode Operation
• USB 2.0 to ATA Native Bridge Controller: CY7C68300B
• Complies with T13's ATA/ATAPI-6 Draft Specification:
  • PIO Mode 0, 3, 4
  • Ultra DMA Mode 2, 4
  • Ultra DMA Mode 0 ~ 4
  • Supports 48-bit addressing for large hard drives (>128GB).
• IDE (ATA/ATAPI) Interface: Male IDC 2X20 Connector
• The IDE (ATA/ATAPI) port supports multi-LUN function for attaching two (Master and Slave) IDE devices.
• Both ATA and ATAPI devices are supported using the same firmware.
• Power indicator LED and HDD Access LED

• 89.5 cm (W) x 62 cm(D)
• Form Factor
  • PCI Bracket Form Factor
  • Fit to most standard PC Case

• U2H4+ATA11P Bridge Board
• CB-00136 - A Plug -to- B Plug USB 2.0 cable in length of 1.5m
• CB-00292 - Ultra DMA100 Cable 12+6 inch for two devices (Black - Gray - Black)
• Installation Guide

Additional Buy:

• ATX-PS01 ATX Power Controller
• SATAMR01 Mobile Rack for 3.5" SATA HDD
• VP-1028LSF USB to IDE Mobile Rack for 3.5" IDE HDD
• DB-525U2i Front Connect 5.25" device bay
• DH-SCR12R USB to Smart & Memory Card Reader
• DH-2CR43R-X USB Memory Card Reader
• DB35U2H401 USB2.0 4-Port HUB
• U2IDE31P USB to ATA RAID Bridge Board
• CB-00281 Two USB B Plug Cable
• CB-00378 One USB B Plug Cable

under construction

Q'ty	Carton size(cm)	N.W.	G.W.	Remark
NA	65x40.8x28.5	NA	NA	CT0001
NA	53.5x34x29	NA	NA	CT0009